The M4A1 AR15 style firearm features the RIS II picatinny quad rail, which has been in use by US Special Operations Command (SOCOM) for the SOPMOD Block II program since 2005. The M4A1 is built around a 14.5 inch Cold Hammer Forged M4 Profile barrel with a permanently attached Dead Air KeyMo Flash Suppressor. The independently ambidextrous GRIP-N-RIP Charging Handle accommodates left- and right-handed shooters. This rifle uses Daniel's fully-ambidextrous DD4 Lower that normally only comes on their RIII series of rifles. The Trigger has been upgraded to a Geissele SSA (Super Semi-Automatic) that offers a two-stage 4.5lb trigger pull. This M4A1 comes coated from the factory in Daniel's Arid Rattlecan Cerakote finish. This rifle also comes with the ergonomic Daniel Defense Buttstock and Pistol Grip.
To top it all off, the rifle comes with a total of FIVE (5) of their 32 round magazines and comes packed in a large FDE rifle case
- LOWER RECEIVER: DD4 Ambidextrous lower with Enhanced Flared Magazine Well and Rear Receiver QD Swivel Attachment Point. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
- UPPER RECEIVER: Mil-Spec with Indexing Marks and M4 Feed Ramps. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
- BARREL: Chrome Moly Vanadium Steel, Cold Hammer Forged, 1:7 Twist, 14.5" M4 Profile, Chrome Lined, Mil-Spec Heavy Phosphate Coated, and HP/MPI Tested
- GAS SYSTEM: Pinned Low Profile Gas Block CNC Machined of 4140 Hardened Steel with Mil-Spec Heavy Phosphate Coating, Carbine Length, Direct Impingement
- MUZZLE DEVICE: Pinned and Welded Dead Air Three-prong Flash Suppressor
- BOLT CARRIER GROUP: M16 Profile, Mil-Spec MP Tested, Chrome Lined, Properly Staked Gas Key
- BUFFER: H Buffer
- TRIGGER: Geissele SSA (Super Semi-Automatic) two-stage, 4.5lb pull.
- SIGHTS: Sold Separately
- HANDGUARD: Daniel Defense M4A1 Rail Interface System (RIS) II, CNC Machined of 6061-T6 Aluminum
- CHARGING HANDLE: GRIP-N-RIP Charging Handle, Body CNC Machined of 7075-T6 Aluminum, Handles & Latch CNC Machined of 6061-T6 Aluminum, Heavy Duty Stainless Steel Roll Pins, Type III Hard Coat Anodized
- RECEIVER EXTENSION: 6 Position Mil-Spec 7075-T6 Aluminum
- BUTTSTOCK: Daniel Defense Buttstock, Glass Filled Polymer with Soft Touch Overmolding
- PISTOL GRIP: Daniel Defense Pistol Grip, Glass Filled Polymer with Soft Touch Overmolding
- RAIL PANELS: Daniel Defense Rail Panels made from Santoprene, heat resistant to 300° F.
- MAGAZINES: Daniel Defense 32-round Magazine x5
- Made in the USA!
* All NFA Regulations apply. Each state’s laws dictate what can or cannot be possessed in its own state. Some county’s within each state are different as well. Please contact your local ATF Field office with any ATF questions or concerns you may have. Freedom Trading Co reserves the right to use discretion when selling to each individual state.
TEST FIRE DISCLAIMER: Many of the manufacturers whose products we carry will have a standardized test fire protocol for not only their complete firearms as well as parts such as upper receiver groups and bolt carriers. Because of this test fire protocol, some items will show evidence of the test fire process such as brass and carbon residue on internals or brass markings on case deflectors.
All firearms must be compliant with your local regulations and shipped to a valid FFL dealer. Please make sure your purchase is in line with your local and state restrictions before making your purchase. You must name your receiving FFL dealer before your item can be shipped and please be aware the shipping can be delayed if your receiving dealer fails to supply the necessary information for your item to be shipped.
|
Daniel Defense M4A1 
